# How White Balance Calibration Helps Your Flight Simulator

• BenQ
• 2021-11-25

As modern flight simulators have evolved to the use of video systems that feature increasingly sophisticated setups – from high horizontal and vertical field of vision screens to multi-projector arrangements – attention to detail has become vital in producing the immersive experience that designers desire. One of the aspects that must be on point in order to optimize the effectiveness of such flight simulators is the color consistency between each projected image, since it’s the cornerstone for creating a seamless whole out of multiple images. This is due to the fact that when the colors in one image are noticeably different than the colors in a neighboring image, the viewer will be instantaneously aware of this disparity, and in the case of a pilot-in-training this may lead to a level of distraction not ideal in such a mentally intensive activity.

Color consistency between each projected image is the cornerstone for creating a seamless whole out of multiple images

So how should the designer of a flight simulator approach this problem to ensure that they build a simulator where each projected image looks uniform in the pilot’s eyes? To answer that question, we will need to first dive into the concept of color difference, particularly how it is calculated, and then follow up by exploring the different ways a designer can minimize color differences with available technology.

## Measuring Color Difference: CIELAB and Delta E

When discussing color difference, experts tend to rely on the three-dimensional CIELAB color space defined by the International Commission on Illumination (CIE for short). This is because the three numerical values that the CIELAB color space uses to define the coordinates of each color in the visual spectrum (L* for lightness, and a* and b* for the four colors of human vision: red, green, blue, and yellow) allows for an accurate and consistent quantification of the difference between any two colors, even colors with the slightest of differences. The value used to represent the difference between two colors in the CIELAB space is known as the Delta E and is derived by essentially calculating the distance between the coordinates of the two colors.

With Delta E in hand, experts have helped define the various magnitudes of color difference as observed by a viewer:

 Delta E < 1 The viewer does not notice any difference between the two colors. 1 < Delta E < 2 Only an experienced viewer can notice the difference between the two colors. 2 < Delta E < 3.5 An unexperienced viewer can notice the difference between the two colors. 3.5 < Delta E < 5 A clear difference between the two colors can be noticed by all. 5 < Delta E The viewer sees two different colors
Correcting Color Difference Using a Projector’s Built-In Features

Differences in color between projectors are unavoidable. Regardless of whether the projectors are produced by different manufacturers or are models from the exact same assembly line, the number of optical components involved in each projector’s design – from the light source to the color wheel to the lens – is bound to create variations due to the cumulative effect of the deviations, however minute, between each of these components. All manufacturers are well aware of this fact, so nearly all projectors on the market include some kind of feature, for example configurable R/G/B Gain settings, which allow the user to make manual adjustments to the color of the projected image.

Most projectors offer some type of white balance adjustment feature (such as R/G/B gain) that allows you to make manual adjustments for color consistency

For designers of flight simulators this then means that regardless of the projectors they choose, they or the systems integrators (SI) who maintain their designs, will be able to adjust the projector’s colors to how they see fit even after completion of the installation process in order to achieve color consistency. With these types of built-in color correction features, systems integrators can attain a Delta E of around 3 across each projected image without much time and effort, while an expert with tools such as a color meter can achieve Delta E values of about 2 depending on the time spent.

Introducing BenQ’s Factory White Balance Adjustment

As mentioned above, most projectors on the market offer some type of color correction features that allow for the manual adjustment of colors. But even though these features do offer those that design, install, and/or maintain flight simulators a decent level of control over the color consistency of their video systems, the extent to which they can ensure true color consistency still requires a degree of effort and cost which might be burdensome, since as mentioned above a Delta E of 2 requires having either an expert with related tools on hand or having an SI (also with tools) spend a fair amount of time tinkering with the projector’s settings.

A more sensible solution would be to have the projectors used be pre-calibrated to a consistent color level prior to shipment, which is where BenQ’s white balance pre-calibration technology, the technology behind BenQ’s Factory White Balance Adjustment (WBA), comes into play. Whereas the process other manufacturers use to pre-calibrate their projectors simply rely on color experts at the production site performing time-intensive manual calibrations similar to the ones discussed above – and at a cost that is passed down to the end-consumer – BenQ’s white balance pre-calibration utilizes cutting-edge technology that allows them to achieve consistently lower Delta E values at a lightning-quick speed that doesn’t affect production costs. So while competitors with their traditional method may spend a chunk of time per projector to obtain a Delta E of 3, BenQ’s white balance pre-calibration technology is able to achieve a Delta E of about 2 at one-fifth to one-tenth of the time.

Color gamut diagrams before and after white balance calibration

The reason pre-calibrating white balance has such an effect on reducing color difference and boosting color consistency is because for the vast majority of frames in a video, the pre-dominant on-screen colors are white or have elements of white in them. One only has to think of how many videos feature the sky (particularly flight simulation videos) or bright backgrounds to get a feel for the role white plays in overall color, similar to why painters paint on a white canvas. In this sense focusing on getting a uniform white between projected images, which BenQ’s pre-calibration technology does, ensures that the backgrounds of those images easily blend into one another which then invariably leads viewers to see a consistency of color.

Edge blending projected images is like multi-canvas painting: first paint each canvas the same white, then add on the other colors for a unified effect

## See BenQ Projectors with BenQ Factory WBA

The following are models from BenQ’s Installation series of projectors that feature BenQ Factory WBA which we recommend for flight simulators.