Visit BenQ Education website for education solutions
product-img

EH600 1080p Smart Wireless Meeting Room Projector

Designed for Knowledge Workers in the New Hybrid Working Era

Application

Can I control the BenQ projector with a remote control designed by other manufacturers?
Yes. When setting the remote control, please input the [custom code + IR code] or [IR code + custom code] based on the instruction on the remote control. The custom code for BenQ is 0X30. For IR code, please refer to the user manual.
Which reminder messages will stop being displayed after "Reminder Message" is switched off?
After "Reminder Message" option is switched off in OSD, the following messages will stop being displayed:
- All signal searching…
- No signal
- (Source) Source searching…
- (Source) Source detected
- Auto adjusting…
- Signal status(Source information menu)
- ECO BLANK/No source detected
- Out of range
- Best resolution

How can I update Android versions via USB drive on BenQ smart projectors?
Please refer to the below video to find out how to update the Android operating system on BenQ smart projectors using a USB drive:
Learn more
How do I mute the projector?
The projector can be muted using one of the following settings -
1. OSD > System setup > audio settings > mute
2.. Mute key on remote
The mute function will reset to default (Off) when the projector is restarted, which means audio will be on.
Therefore, if you wish to mute the projector permanently, please turn the audio volume down to 0. Volume levels do not reset for power cycles or restarts.
The projector is not listed as detected by my device even though they're on the same Wi-Fi network. What can I do to enable wireless projection?
Please check your router settings to see if there's any access restriction like AP isolation and whether UDP port 5053 and 1900 are taken up or blocked. If so, please disable and unblock those access restrictions and try again. Thank you.
How can I manage screen mirroring authority on my projector?
Follow the below steps to manage screen mirroring authority on your projector. Step 1 Go to BenQ Suggest
How to manual upgrade android firmware on Smart projector?
Please refer to the step-by-step video tutorial for updating firmware via a USB disk.
Learn more
How can I wirelessly project my Windows PC to the projector?
For wirelessly projecting your Windows PC to the projector, please refer to the following tutorial video:
Learn more
How can I do screen-mirroring on a smart projector?
Please refer to the below video for information on smart projector screen-mirroring with a range of devices:
Learn more
Does the projector support change slides on PowerPoint using a remote which emulates page up and page down commands for both Windows PC and MacOS?
How can I change the projector's name?
How to replace the projector lamp and reset the lamp timer?
How do I clean my projector lens?
It is normal to have some dust on the lens surface. Please refer to the below video for a guide to cleaning your projector's lens.
Learn more

Specification

Which types of BenQ projectors require a power cycling process?
For BenQ projectors designed for general home entertainment and business use, we recommend powering off the projector for 2-3 minutes after every 12 hours of constant use for longer lasting reliability and maximized projector lifespan. BenQ professional projectors designed with corresponding industrial standards can be used continuously for more than 12 hours and do not require a power cycling process as our home and general-use business projectors do. If you have any questions, please contact your local BenQ customer care team for further assistance. Thank you.
Learn more
The Wired remote port is used to connect to a wired remote control. What is the maximum distance supported by the wired remote control?

Further Query

Which types of BenQ projectors require a power cycling process?
For BenQ projectors designed for general home entertainment and business use, we recommend powering off the projector for 2-3 minutes after every 12 hours of constant use for longer lasting reliability and maximized projector lifespan. BenQ professional projectors designed with corresponding industrial standards can be used continuously for more than 12 hours and do not require a power cycling process as our home and general-use business projectors do. If you have any questions, please contact your local BenQ customer care team for further assistance. Thank you.
Learn more
The Wired remote port is used to connect to a wired remote control. What is the maximum distance supported by the wired remote control?
My remote control is not working. What can be done to fix it?
Please follow below steps for troubleshooting:
(1) Check if the remote receiver is turned off by accident in OSD. It should be turned to Front/Top/Front+Top.
(2) Check if the batteries are out of power. Replace both of the batteries with new ones.
(3) Make sure you are not too far away from the projector. Stand within 7 meters from the projector.
(4) Remove the obstacles between the remote control and projector.
For demo, please refer to the tutorial video
Learn more
Why can’t I use a QR code to log in to the AMS system when the projector is turned on?
"The Android operating system automatically synchronizes the time from the network about 5-10 seconds after getting connected to the Internet. When the correct time is displayed on the Launcher, you can log in to the AMS system using a QR code.
Learn more
“Untrusted device” message pops up on my smartphone when I tried to cast YouTube to my projector. How can I fix it?
How can I avoid the DLP Link signal getting lost sync when watching the Blue-Ray 3D video?
Can I control the BenQ projector with a remote control designed by other manufacturers?
Yes. When setting the remote control, please input the [custom code + IR code] or [IR code + custom code] based on the instruction on the remote control. The custom code for BenQ is 0X30. For IR code, please refer to the user manual.
Which reminder messages will stop being displayed after "Reminder Message" is switched off?
After "Reminder Message" option is switched off in OSD, the following messages will stop being displayed:
- All signal searching…
- No signal
- (Source) Source searching…
- (Source) Source detected
- Auto adjusting…
- Signal status(Source information menu)
- ECO BLANK/No source detected
- Out of range
- Best resolution

How can I update Android versions via USB drive on BenQ smart projectors?
Please refer to the below video to find out how to update the Android operating system on BenQ smart projectors using a USB drive:
Learn more
How do I mute the projector?
The projector can be muted using one of the following settings -
1. OSD > System setup > audio settings > mute
2.. Mute key on remote
The mute function will reset to default (Off) when the projector is restarted, which means audio will be on.
Therefore, if you wish to mute the projector permanently, please turn the audio volume down to 0. Volume levels do not reset for power cycles or restarts.
The projector is not listed as detected by my device even though they're on the same Wi-Fi network. What can I do to enable wireless projection?
Please check your router settings to see if there's any access restriction like AP isolation and whether UDP port 5053 and 1900 are taken up or blocked. If so, please disable and unblock those access restrictions and try again. Thank you.
How can I manage screen mirroring authority on my projector?
Follow the below steps to manage screen mirroring authority on your projector. Step 1 Go to BenQ Suggest
How to manual upgrade android firmware on Smart projector?
Please refer to the step-by-step video tutorial for updating firmware via a USB disk.
Learn more
How can I wirelessly project my Windows PC to the projector?
For wirelessly projecting your Windows PC to the projector, please refer to the following tutorial video:
Learn more
How can I do screen-mirroring on a smart projector?
Please refer to the below video for information on smart projector screen-mirroring with a range of devices:
Learn more
Does the projector support change slides on PowerPoint using a remote which emulates page up and page down commands for both Windows PC and MacOS?
How can I change the projector's name?
How to replace the projector lamp and reset the lamp timer?
How do I clean my projector lens?
It is normal to have some dust on the lens surface. Please refer to the below video for a guide to cleaning your projector's lens.
Learn more