Visit BenQ Education Website for education solutions
product-img product-img

LU9715 8000lms WUXGA Large-Venue

BlueCore Laser Projectors from the World’s No.1 DLP Brand

Application

Can I control the BenQ projector with a remote control designed by other manufacturers?
Yes. When setting the remote control, please input the [custom code + IR code] or [IR code + custom code] based on the instruction on the remote control. The custom code for BenQ is 0X30. For IR code, please refer to the user manual.
Which reminder messages will stop being displayed after "Reminder Message" is switched off?
After "Reminder Message" option is switched off in OSD, the following messages will stop being displayed:
- All signal searching…
- No signal
- (Source) Source searching…
- (Source) Source detected
- Auto adjusting…
- Signal status(Source information menu)
- ECO BLANK/No source detected
- Out of range
- Best resolution

How to use 3D sync out connector?
There are two types of 3D sync out connectors. For the steps to use 3D sync out connectors, please refer to the tutorial video.
Learn more
Is it normal that the power LED flashes orange for around 10 seconds then becomes solid red, after the projector is turned on?
Yes, it is normal. When network standby mode is enabled, the power LED will flash until the power supply becomes stable.
In OSD display, there is pincushion/ barrel option. May I know what is it?
When you select pincushion/barrel in OSD, then press direction key, you will see the image to become pincushion or barrel.
When you press right key (value>0), the image will be in barrel shape.
When you press left key (value<0), the image will be in pincushion shape.
Is LU9715 equipped with ID SET feature for remote controller?
Units manufactured after Aug., 2016 are equipped with this feature. Please contact with local BenQ authorized service center for firmware upgrading if your LU9715 is without this feature.
How do I mute the projector?
The projector can be muted using one of the following settings -
1. OSD > System setup > audio settings > mute
2.. Mute key on remote
The mute function will reset to default (Off) when the projector is restarted, which means audio will be on.
Therefore, if you wish to mute the projector permanently, please turn the audio volume down to 0. Volume levels do not reset for power cycles or restarts.
How to use 3D sync out connector?
There are two types of 3D sync out connectors. For the steps to use 3D sync out connectors, please refer to the tutorial video.
Learn more
Does the projector support change slides on PowerPoint using a remote which emulates page up and page down commands for both Windows PC and MacOS?
How do I clean my projector lens?
It is normal to have some dust on the lens surface. Please refer to the below video for a guide to cleaning your projector's lens.
Learn more

Specification

Is the baud rate of the projector changeable?
No. The default baud rate is 9600 and cannot be changed.
Learn more
Which types of BenQ projectors require a power cycling process?
For BenQ projectors designed for general home entertainment and business use, we recommend powering off the projector for 2-3 minutes after every 12 hours of constant use for longer lasting reliability and maximized projector lifespan. BenQ professional projectors designed with corresponding industrial standards can be used continuously for more than 12 hours and do not require a power cycling process as our home and general-use business projectors do. If you have any questions, please contact your local BenQ customer care team for further assistance. Thank you.
Learn more
How long is the suggested working time for models which light source is UHP lamp?
It is suggested to power cycle at least every 12 hours for more stable performance.
The Wired remote port is used to connect to a wired remote control. What is the maximum distance supported by the wired remote control?

Further Query

Is the baud rate of the projector changeable?
No. The default baud rate is 9600 and cannot be changed.
Learn more
Which types of BenQ projectors require a power cycling process?
For BenQ projectors designed for general home entertainment and business use, we recommend powering off the projector for 2-3 minutes after every 12 hours of constant use for longer lasting reliability and maximized projector lifespan. BenQ professional projectors designed with corresponding industrial standards can be used continuously for more than 12 hours and do not require a power cycling process as our home and general-use business projectors do. If you have any questions, please contact your local BenQ customer care team for further assistance. Thank you.
Learn more
How long is the suggested working time for models which light source is UHP lamp?
It is suggested to power cycle at least every 12 hours for more stable performance.
The Wired remote port is used to connect to a wired remote control. What is the maximum distance supported by the wired remote control?
My remote control is not working. What can be done to fix it?
Please follow below steps for troubleshooting:
(1) Check if the remote receiver is turned off by accident in OSD. It should be turned to Front/Top/Front+Top.
(2) Check if the batteries are out of power. Replace both of the batteries with new ones.
(3) Make sure you are not too far away from the projector. Stand within 7 meters from the projector.
(4) Remove the obstacles between the remote control and projector.
For demo, please refer to the tutorial video
Learn more
May I know the version of DisplayPort of LU9715?
The version of LU9715 DisplayPort is 1.1a.
How does LU9915 3D sync in/ out feature work with other device?
3D sync in is for some scenarios that need to link two or more projectors for displaying 3D content. It can receive the 3D sync. signal from the source (ex. computer’s display card) or another projector.
For example, multiple projectors to display a blended (extended to wider screen) 3D picture, the projectors needed to be synchronized.
Or for using 2 projectors to display one 3D picture (overlapped for brighter picture) and each projector is responsible for one eye’s picture (one for right eye and one for left eye).
As Abobe Flash support ends at the end of Dec 2020, the Crestron network interface will no longer work after that. Is there any solution for this?
3D is not working or getting lost sync on my projector. How can I fix it?
Can I control the BenQ projector with a remote control designed by other manufacturers?
Yes. When setting the remote control, please input the [custom code + IR code] or [IR code + custom code] based on the instruction on the remote control. The custom code for BenQ is 0X30. For IR code, please refer to the user manual.
Which reminder messages will stop being displayed after "Reminder Message" is switched off?
After "Reminder Message" option is switched off in OSD, the following messages will stop being displayed:
- All signal searching…
- No signal
- (Source) Source searching…
- (Source) Source detected
- Auto adjusting…
- Signal status(Source information menu)
- ECO BLANK/No source detected
- Out of range
- Best resolution

How to use 3D sync out connector?
There are two types of 3D sync out connectors. For the steps to use 3D sync out connectors, please refer to the tutorial video.
Learn more
Is it normal that the power LED flashes orange for around 10 seconds then becomes solid red, after the projector is turned on?
Yes, it is normal. When network standby mode is enabled, the power LED will flash until the power supply becomes stable.
In OSD display, there is pincushion/ barrel option. May I know what is it?
When you select pincushion/barrel in OSD, then press direction key, you will see the image to become pincushion or barrel.
When you press right key (value>0), the image will be in barrel shape.
When you press left key (value<0), the image will be in pincushion shape.
Is LU9715 equipped with ID SET feature for remote controller?
Units manufactured after Aug., 2016 are equipped with this feature. Please contact with local BenQ authorized service center for firmware upgrading if your LU9715 is without this feature.
How do I mute the projector?
The projector can be muted using one of the following settings -
1. OSD > System setup > audio settings > mute
2.. Mute key on remote
The mute function will reset to default (Off) when the projector is restarted, which means audio will be on.
Therefore, if you wish to mute the projector permanently, please turn the audio volume down to 0. Volume levels do not reset for power cycles or restarts.
How to use 3D sync out connector?
There are two types of 3D sync out connectors. For the steps to use 3D sync out connectors, please refer to the tutorial video.
Learn more
Does the projector support change slides on PowerPoint using a remote which emulates page up and page down commands for both Windows PC and MacOS?
How do I clean my projector lens?
It is normal to have some dust on the lens surface. Please refer to the below video for a guide to cleaning your projector's lens.
Learn more